Dust Suppression in Mining

Where mine dust comes from and how it is prevented, captured and measured.

Loading the animation…
You are watching a free lesson. A free account saves your progress and lets you mark lessons complete. Create a free account Sign in

What dust suppression does

Mining breaks, moves and crushes rock, and every one of those steps can put fine dust into the air. Dust suppression stops the dust getting into the air in the first place, captures what is released, and dilutes what is left, so that people breathe less than the exposure limit.

The dust that matters most is the dust you cannot see. Very fine particles stay in the air for a long time and reach deep into the lungs. An open pit has a few main sources: the blast, the haul trucks on unsealed roads, the primary crusher, the conveyor transfers and the stockpiles. Each source has its own control. Underground mines use the same ideas, with water sprays at the cutting face and ventilation air that carries the dust away.

How it works

  1. 1Blasting. A blast lifts a large cloud for a short time. Good stemming, the crushed rock packed into the top of each hole, keeps the energy in the rock. The shot is fired when the wind carries the plume away from people, and an exclusion zone keeps everyone clear until the dust has gone.
  2. 2Haul roads. Truck tyres on a dry road are often the largest source of dust in a pit. A water cart (see haul road watering) sprays the road so the surface stays damp, sometimes with a suppressant in the water. A truck on the wet lane lifts far less dust than a truck on the dry lane.
  3. 3Crusher tip. When a truck tips into the crusher, the falling rock pushes dusty air out of the hopper. A fog cannon (see the fog cannon lesson) or a ring of water sprays throws fine droplets into that air. Droplets and dust particles collide, stick together and fall.
  4. 4Conveyor transfer. Where one belt drops ore onto the next (see transfer point dust collection), an enclosure with rubber skirts holds the dust in. A hood and a duct pull the dusty air to a dust collector, where filter bags trap the dust and a fan sends the clean air out.
  5. 5Stockpile. Wind lifts dust from the surface of the pile and from the falling stream of ore. Water sprays keep the surface damp, or a suppressant that forms a crust binds it.
  6. 6Monitoring. A dust monitor measures the dust in the air around the site, and small samplers worn by workers measure what people actually breathe. The results are compared with the exposure limit, and the controls are improved where they fall short.

The numbers

Dust is measured in milligrams per cubic metre of air (mg/m³), averaged over a shift. Respirable dust is the fine part, roughly smaller than 10 micrometres, which is far too small to see as single particles. Exposure limits for respirable dust and for respirable crystalline silica are set by each state regulator. They are small fractions of a milligram per cubic metre and they have been tightened in recent years, so check the current limit for your state.

ItemTypical value
Water on a haul roadabout 1 to 2 L per m² per pass
Air-to-cloth ratio of a bag filterabout 1 m/min, depending on the dust
Fog dropletsfine, close to the size of the dust they must catch
Order of controlsprevent first, then capture, then dilute

Worked example. Assume a 4 km haul road, 30 m wide, watered at 1.5 L per m² on each pass, 6 passes in a shift, with an 80,000 L water cart. Assume also a dust collector on a transfer point that draws 10 m³/s of air at an air-to-cloth ratio of 1 m/min, with filter bags 150 mm in diameter and 3 m long.

QuantityWorkingResult
Road area4,000 × 30120,000 m²
Water for one pass120,000 × 1.5180,000 L (180 kL)
Cart loads for one pass180,000 ÷ 80,0002.25 loads
Water in a shift6 × 1801,080 kL, about 1.1 ML
Air through the collector10 × 60600 m³/min
Filter cloth area600 ÷ 1600 m²
Cloth area of one bag3.14 × 0.15 × 3about 1.41 m²
Number of bags600 ÷ 1.41about 425 bags

The example shows why road watering is a large water user on a mine, and why a dust collector for one transfer point is a large machine. Water alone is not enough on a hot, windy day, and a road that is wetted too much turns slippery and muddy.

Assumed inputs, not data from a particular plant or mine. Watering rates, filter ratios and exposure limits vary by site, by dust and by state.

Safety: respirable crystalline silica and coal dust can cause serious lung disease, and the harmful dust is too fine to see. A site that looks clean is not proof of safe air. This lesson is general education, not a procedure: follow the dust management plan of your site and check the current exposure limit for your state.

What the operator watches

  • Visible dust and the wind. A plume that leaves the source shows a control is not working, and the wind direction shows who it will reach.
  • Water cart cycle and road condition. The road should stay damp, not dry and pale, and not muddy.
  • Dust collector pressure drop. A rising pressure across the filter bags means they are blocking. A sudden fall can mean a torn bag.
  • Monitor readings. The dust monitor and the personal samples are compared with the limit, not with how the site looks.

Common problems

  • Water dries faster than it is applied. On hot, windy days the road is dry again before the cart returns.
  • Blocked nozzles. Dirty water blocks spray and fog nozzles, and the dust escapes where the spray is missing.
  • Torn bag or worn skirts. A torn filter bag lets dust straight through the collector, and worn skirts let the transfer leak.
  • Too much water. Over-watered roads are slippery, and wet ore sticks to belts and blocks chutes.

Words you will meet

Respirable dust
Dust fine enough to reach deep into the lungs.
Crystalline silica
Quartz, a common mineral in rock. Its respirable dust causes the lung disease silicosis.
Exposure limit
The most dust a person may breathe, as an average over a shift (a time-weighted average, TWA).
Stemming
Crushed rock packed into the top of a blast hole to hold the energy in.
Suppressant
A product added to water so it wets dust better or binds the surface into a crust.
Fog cannon
A fan with a ring of nozzles that throws a cloud of fine water droplets.
Skirt
A rubber strip that seals the gap between a chute and the belt.
Dust collector (baghouse)
A filter that pulls dusty air through fabric bags and lets clean air out.

Check your understanding

Why is monitoring part of dust control?

The harmful dust is too fine to see, so controls are judged by what people actually breathe, measured against the exposure limit, and not by what looks clean.

Why does a conveyor transfer need extraction as well as an enclosure and skirts?

Falling ore pushes air out of the enclosure, and the air carries dust with it. Extraction pulls that air through the hood to the dust collector, so air flows into the enclosure through the gaps and not out of them.

A road of 120,000 m² is watered at 1.5 L per m². How many loads of an 80,000 L cart is one pass?

120,000 × 1.5 = 180,000 L, and 180,000 ÷ 80,000 = 2.25 loads.

Key facts

Order of controls
Prevent the dust, then capture it, then dilute what is left.
Largest source
Often the haul roads, because trucks run on them all day.
Road watering
Typically about 1 to 2 L per m² per pass, repeated as the road dries.
Bag filter
Air-to-cloth ratio typically about 1 m/min.
Exposure limits
Set by each state and tightened in recent years. Check the current limit for your state.
Use the animation
Follow the numbers 1 to 6 on the drawing: they match the steps on this page, in the same order. The brown puffs are dust. Watch them shrink where a control acts: on the wet lane behind the water cart, in the mist of the fog cannon and at the hood of the transfer. Hover over any part for its name, and click a part with its own lesson to open it.