Grind bauxite, dissolve alumina in caustic soda, settle the mud, grow crystals, calcine.
Aluminium metal is made from alumina, a white powder of aluminium oxide. Alumina is made from bauxite, a red-brown ore that holds aluminium as aluminium hydroxide, mixed with iron oxides, silica and other minerals. An alumina refinery separates the aluminium from the rest. Most of the world's alumina is made by the Bayer process: dissolve the alumina in hot caustic soda, throw away the part that does not dissolve, then grow crystals of aluminium hydroxide from the liquor and heat them to alumina.
The caustic soda liquor goes round a loop and is used again and again. Heat is moved from stream to stream so that as little fresh steam as possible is needed. The ore arrives crushed and the front of the plant is much like any mineral processing plant. What is special is the chemistry after the mill. Each major unit has its own lesson: click it in the animation.
The solids go one way through the plant: bauxite to red mud on one side, alumina on the other. The caustic liquor goes round in a loop.
Typical features: a refinery needs typically 1.9 to 3.6 t of bauxite for each tonne of alumina, depending on how rich the bauxite is, and leaves typically 1 to 1.5 t of red mud for each tonne of alumina. Digestion runs typically at about 140 to 150°C for soft gibbsitic bauxite and hotter for other bauxite types. The liquor is cooled to typically 50 to 80°C for precipitation, and the crystals take typically a day or more to grow. Calcination runs at about 1,000 to 1,100°C. The chemistry is: digestion, Al(OH)3 + NaOH gives NaAl(OH)4; precipitation is the same reaction run backwards; calcination, 2 Al(OH)3 gives Al2O3 + 3 H2O.
Worked example, a balance. Assume a refinery that makes 1,000,000 t of alumina a year in 8,000 operating hours, 2.5 t of bauxite for each tonne of alumina, 1.2 t of dry red mud for each tonne of alumina, and a slurry of 600 t/h to heat from its start temperature by 45°C (specific heat about 3.2 kJ/kg K) with steam that gives up 2,000 kJ/kg as it condenses.
| Quantity | Working | Result |
|---|---|---|
| Alumina each hour | 1,000,000 ÷ 8,000 | 125 t/h |
| Bauxite each hour | 125 × 2.5 | 312.5 t/h, about 313 t/h |
| Red mud each hour (dry) | 125 × 1.2 | 150 t/h |
| Hydrate to the calciner (molar masses: 2 Al(OH)3 = 156, Al2O3 = 102) | 125 × 156 ÷ 102 | 191 t/h |
| Water driven off in the calciner | 191 − 125 | 66 t/h |
| Heat to warm the slurry | 600,000 × 3.2 × 45 ÷ 3,600 | 24,000 kW, 24 MW |
| Steam needed | 24,000 × 3,600 ÷ 2,000 | 43,200 kg/h, about 43 t/h |
| Red mud each year | 150 × 8,000 | 1,200,000 t |
In a real plant most of the heating is done by heat recovered from the hot streams, so the steam needed is much less than the figure shown. The drawing shows one heater and three digesters. A real plant has several heating stages and more vessels.
Assumed inputs, not data from a particular plant. The bauxite and red mud for each tonne, the temperatures and the heat duty change with the bauxite and the design.
Safety: hot, strong caustic soda liquor burns skin and eyes, the digesters hold hot pressurised liquor and steam, the calciner runs above 1,000°C, and the dry alumina and bauxite make dust. Red mud is strongly alkaline, so its storage must keep the liquid in. The design relies on pressure relief, interlocks, lined and bunded areas, dust control and permits to work. This lesson explains the principle and is not an operating procedure.
After the hydrate is taken out the liquor still holds most of its caustic soda and can dissolve more alumina. Re-using it saves caustic soda. Only the part lost with the red mud and in side reactions is replaced.
The liquor is cooled, so it holds more dissolved alumina than it can keep. The seed crystals give surfaces where the extra alumina can grow as hydrate.
60 × 156 ÷ 102 = 91.8 t/h, about 92 t/h. The extra weight is the bound water that the calciner drives off.