Coal Preparation Plant (CHPP)

Coarse, fine and ultrafine coal washed apart, dewatered, loaded on trains, rejects stored.

Loading the animation…
You are watching a free lesson. A free account saves your progress and lets you mark lessons complete. Create a free account Sign in

What a coal preparation plant does

A coal preparation plant separates coal from the rock that is mined with it. It is also called a wash plant, or a coal handling and preparation plant (CHPP) when the stockpiles and train loading are counted with it. Coal is lighter than rock, so the plant sorts by density: in a heavy liquid the coal floats and the rock sinks.

Run-of-mine (ROM) coal arrives from the pit (see open pit mining). Clean coal leaves by train for a port or a power station, where a coal handling system receives it. The rock and the fine tailings go to disposal, and most of the water is used again.

This page is the map. Each washing circuit has its own lesson with its own animation: the dense medium cyclone, the coal spiral, the flotation cell, dewatering and train loading. Click a machine in the animation to open its lesson.

How it works

No single machine cleans every size of coal, so the plant sorts the feed by size and gives each size its own separator. The drawing is simplified: it shows one machine of each kind, and a real plant has several side by side.

  1. 1Receive, break and size. ROM coal is tipped into a bin and a breaker reduces the big lumps. A conveyor lifts the raw coal to a sizing screen. Water sprays wash the fine particles through the deck, and the coarse coal stays on top.
  2. 2Coarse coal: dense medium cyclone. The coarse coal, typically from 1 or 2 mm up to about 50 mm, drops into a tank of medium, which is water with finely ground magnetite. A pump sends the coal and the medium into a cyclone. The medium is heavier than coal and lighter than rock, so the coal leaves with the overflow and the rock with the underflow. It is built like a hydrocyclone, but it sorts by density, not by size.
  3. 3Fine coal: spiral and flotation cell. The fine particles that fell through the screen travel in water. A classifying cyclone, not drawn here, usually splits them by size. Fine coal, typically about 0.1 to 2 mm, runs down a spiral trough: the heavier rock moves to the inside and the lighter coal stays to the outside, where a splitter cuts it off. The ultrafine particles are too small for gravity to sort. In a flotation cell, air bubbles carry the water-repellent coal to the top as a black froth, and the clay and rock stay in the slurry. For simplicity the drawing feeds the spiral and the cell from one pipe.
  4. 4Dewater the fine coal. The coal from the spiral and the froth from the cell are still very wet. They run onto a vibrating dewatering screen: the water drains through the deck and the damp coal slides off onto the product conveyor. Centrifuges do the same job for the finest coal.
  5. 5Stockpile and load. The clean coal from the cyclone and from the dewatering screen joins on one product conveyor and is stacked on a stockpile. A reclaim conveyor carries it to a loadout bin over the rail track, where trains are loaded, weighed and sampled.
  6. 6Rejects and water. The rock from the cyclone goes by a reject conveyor to the tailings storage. The fine tailings from the spiral and the cell go to a thickener, where the solids settle. The thick underflow is pumped to the tailings storage too, which is the co-disposal some plants use, and the clear water is used again in the plant.

The numbers

Figures are typical and depend on the coal. A plant typically takes from several hundred to about 2,000 tonnes per hour of ROM coal. The medium typically has a relative density of about 1.3 to 1.6, set by the ash wanted in the product. Clean coal has a relative density of about 1.3 to 1.4 and rock about 2.2 to 2.7 (typical values); particles of coal with rock locked in them lie in between, which is why the medium density matters so much. Product yield depends entirely on the coal.

Worked example. Assume a plant fed with 1,000 t/h of ROM coal, a product yield of 65 percent, 7,000 operating hours a year and trains of 10,000 t. Assume also a medium of relative density 1.45, made with magnetite of relative density 5.0.

QuantityWorkingResult
Product coal1,000 × 0.65650 t/h
Reject (rock and tailings)1,000 − 650350 t/h
Product per year650 × 7,0004,550,000 t (4.55 million t)
Reject per year350 × 7,0002,450,000 t (2.45 million t)
Train loads per year4,550,000 ÷ 10,000455 trains, about 1.2 a day
Production needed to fill one train10,000 ÷ 650about 15.4 hours
Magnetite share of the medium, by volume(1.45 − 1) ÷ (5.0 − 1)0.1125, about 11 percent
Magnetite in 1 m³ of medium0.1125 × 5,000 kg/m³about 563 kg, with about 888 kg of water (1,450 kg in total)

About a third of the feed in this example is rock that must be carried away and stored, so the reject and tailings circuit is a large part of the plant. Only about 11 percent of the medium by volume is magnetite, yet it makes a liquid 45 percent heavier than water.

Assumed inputs, not data from a particular plant. Yield, size ranges and medium density depend on the coal and on the plant.

Safety: coal dust can burn and a dust cloud can explode, stockpiled coal can heat up by itself, and the plant is full of moving machines and slurry under pressure. Plants control dust, watch their stockpiles and isolate machines before work. This lesson is education, not a procedure.

What the operator watches

  • Medium density. It sets the cut between coal and rock, so it is measured all the time and corrected with water or magnetite.
  • Magnetite loss. Magnetite that leaves with the product or the reject has to be bought again.
  • Froth and splitters. The colour and load of the flotation froth, and the splitter positions on the spirals, show how the fine circuits are doing.
  • Product ash and moisture. Both are sampled routinely, on the product conveyor and at the train.

Common problems

  • Wrong medium density. Too low sends good coal to reject; too high lets rock into the product.
  • Worn cyclone parts. A worn inlet or underflow opening changes the split and lowers the yield.
  • Clay in the feed. Clay thickens the medium and the slurry, so every separation gets worse and the thickener struggles to give clear water.
  • Wet product. A blinded screen deck or centrifuge basket leaves too much water in the coal.

Words you will meet

ROM coal
Run-of-mine coal: coal as it comes from the mine, with rock still in it.
Ash
What is left when coal is burned. It comes from the rock and clay in the coal.
Yield
The share of the feed that leaves as clean product.
Dense medium
Water made heavier with fine magnetite, so coal floats in it and rock sinks.
Magnetite
A heavy, magnetic iron mineral. A magnet recovers it from the water.
Spiral
A spiral trough that sorts fine coal from fine rock as the slurry runs down.
Dewatering
Taking water out of the wet coal, on a screen or in a centrifuge.
Reject
The coarse rock removed from the coal.
Tailings
The fine waste slurry from the spirals and flotation.
Co-disposal
Storing the coarse reject and the thickened tailings together.

Check your understanding

Why is magnetite added to the water in a dense medium cyclone?

To make a liquid that is heavier than coal and lighter than rock. In it the coal floats to the overflow and the rock sinks to the underflow.

Why do coarse, fine and ultrafine coal use different equipment?

The particle size decides which separation works. Dense medium cyclones suit coarse coal, spirals suit fine coal, and only flotation can clean the ultrafine particles.

Why is the product dewatered before it is stockpiled?

Water adds weight that is paid for in transport, lowers the heating value of the coal and makes it hard to handle.

Key facts

Principle
Coal is lighter than rock, so the plant separates by density.
By size
Dense medium cyclone for coarse coal, spiral for fine coal, flotation for ultrafine coal.
Medium
Water and magnetite, typically at a relative density of about 1.3 to 1.6.
Water
The thickener settles the tailings and the clear water is used again.
Yield
Depends on the coal. The rest of the feed is reject and tailings.
Use the animation
The animation is clickable: click a machine that has its own lesson to open it. Follow the coal from the ROM bin to the sizing screen, then to the dense medium cyclone, the spiral and the flotation cell, the dewatering screen, the stockpile and the train. Colours: coal is black, rock and tailings are grey and water is blue. Look at the glass cyclone and the glass flotation cell to see the inside. The numbers on the drawing match the numbered steps under How it works. Hover over any part for its name and what it does.