What a copper processing plant does
Copper ore usually holds only a small fraction of a percent to about one percent of copper. The plant grinds the ore and floats the copper minerals off as a concentrate. A smelter and a refinery then turn the concentrate into pure copper cathode.
This lesson follows the sulphide route, which is flotation, smelting and refining. Oxide ore takes another route: it is leached with acid (see heap leach) and the copper is recovered by solvent extraction and electrowinning (SX-EW). The first half of the animation is the concentrator described in the mineral processing plant lesson. The second half is the smelter and the refinery, which are often at another site.
How it works
Each stage makes the copper richer and throws away something else: rock, then iron and sulphur, then the last impurities.
- 1Crush and grind. A jaw crusher breaks the ore and a conveyor carries it to the mills. The SAG mill and the ball mill grind it with water, in closed circuit with a hydrocyclone.
- 2Rougher flotation. Air is bubbled through the slurry with reagents. The copper minerals stick to the bubbles and rise as a froth. The rest sinks and leaves as tailings (see the copper flotation circuit and, for one machine, the flotation cell).
- 3Regrind and clean. The rougher concentrate is ground finer in a regrind mill and floated again in cleaner cells (all part of the flotation circuit). This raises the grade and cuts the waste in the concentrate.
- 4Dewater. A thickener and a filter (for example a vacuum disc filter) turn the slurry into a damp concentrate cake that can be shipped (see concentrate dewatering).
- 5Smelt. Dried concentrate is melted in a furnace, for example a flash furnace. Iron and sulphur leave as slag and as sulphur dioxide gas, which is captured and made into sulphuric acid. The copper stays in a molten matte.
- 6Convert and cast anodes. Air is blown through the matte in a converter to make blister copper. The blister is refined in a furnace and cast as anodes (see copper refining).
- 7Electrorefine. The anodes hang in an acid solution. An electric current dissolves them and plates pure copper onto cathodes in the electrorefining cell. Oxide ore takes the SX-EW route instead.
The numbers
Figures are typical and depend on the ore and the plant.
| Stream | Typical copper content |
|---|
| Plant feed (ore) | typically about 0.4 to 1 percent |
| Flotation concentrate | typically about 25 to 30 percent |
| Matte from the smelting furnace | typically about 60 to 70 percent |
| Blister copper from the converter | typically about 98 to 99 percent |
| Cathode from the refinery | typically about 99.99 percent |
Flotation recovery is typically about 85 to 92 percent of the copper in the feed.
Worked example. Assume 1,000 t of ore at 0.8 percent copper, a flotation recovery of 88 percent, a concentrate of 27 percent copper and a matte of 65 percent copper.
| Quantity | Working | Result |
|---|
| Copper in the ore | 1,000 × 0.008 | 8.0 t |
| Copper recovered | 8.0 × 0.88 | 7.04 t |
| Concentrate produced | 7.04 ÷ 0.27 | about 26.1 t |
| Mass pull (concentrate ÷ ore) | 26.1 ÷ 1,000 | about 2.6 percent |
| Ratio of concentration | 1,000 ÷ 26.1 | about 38 to 1 |
| Tailings | 1,000 − 26.1 | about 974 t |
| Matte, if all the copper stays in it | 7.04 ÷ 0.65 | about 10.8 t |
| Cathode copper, if nothing is lost after flotation | the same 7.04 t of copper | about 7 t from 1,000 t of ore |
The tailings are 97 percent of the mass, which is why tailings storage and water recovery matter so much. The last two rows ignore the small losses in the smelter and the refinery.
Assumed inputs, not data from a particular plant.
Safety: a smelter handles molten metal and sulphur dioxide gas, and the acid plant and the refinery handle sulphuric acid. Molten metal reacts violently with water, the gas is toxic and the acid burns. Gas capture, dry working areas and protective equipment are part of the design. This lesson explains the process; it is not a procedure.
What the operator watches
- Mill power and grind size. The grind decides how well the copper minerals are freed from the rock.
- Froth and reagents. The look and level of the froth in the cells, and the reagent dosing, show how flotation is working.
- Concentrate grade and recovery. A higher grade usually costs some recovery, so both are tracked together.
- Thickener underflow density and filter cake moisture. The cake must be dry enough to handle and ship.
Common problems
- Grind too coarse. Copper stays locked in the rock and is lost to tailings.
- Grind too fine, or slimes. Very fine particles float badly and can coat the copper minerals.
- Clay in the ore. Clay thickens the slurry and lowers flotation performance.
- Pyrite in the concentrate. Pyrite (iron sulphide) can float with the copper and dilute the concentrate.
- Changes in water chemistry. The plant reuses its water, so a shift in the water changes how the reagents work.
Words you will meet
- Concentrate
- The small, copper-rich product of flotation.
- Rougher, cleaner
- The first flotation cells, which recover the copper, and the later cells, which raise the grade.
- Regrind
- Grinding the rougher concentrate finer to free the copper minerals.
- Recovery and grade
- The share of the copper that is caught, and the percentage of copper in a stream.
- Mass pull
- The share of the feed mass that leaves as concentrate.
- Matte
- The molten mix of copper, iron and sulphur made in the smelting furnace.
- Blister copper
- The impure copper made in the converter.
- Anode and cathode
- The cast blister plate that dissolves in the refinery, and the pure copper sheet that grows there.
Check your understanding
Why is a concentrate made at the mine, when the ore could be sent straight to the smelter?
The ore is under one percent copper and the concentrate is about thirty percent. Shipping and smelting the concentrate is far cheaper than shipping and smelting all the rock.
What does the regrind circuit do?
It grinds the rougher concentrate finer to free the copper minerals, so the cleaner cells can raise the grade.
What happens to most of the ore mass in flotation?
It leaves as tailings. In the example the tailings are about 974 t of every 1,000 t of ore, over 95 percent of the feed.
Key facts
- Ore
- Typically about 0.4 to 1 percent copper.
- Concentrate
- Typically about 25 to 30 percent copper, a few percent of the ore mass.
- Smelter
- Matte typically about 60 to 70 percent copper, blister about 98 to 99 percent.
- Cathode
- Typically about 99.99 percent copper.
- Tailings
- Most of the ore mass, over 95 percent in the example.
The animation is clickable: click the crusher, the conveyor, a mill, the pump, the cyclone, any part of the flotation bank (rougher and cleaner cells, launders, regrind mill), the concentrate thickener, the filter, the flash furnace, the converter, the anode wheel, the refinery cell, the tailings thickener or the tailings storage to open its own lesson. Follow the ore through the mills to the rougher cells, the froth through the regrind mill and the cleaners, and the concentrate through the thickener and the filter. Then follow it into the smelting furnace, the converter, the anode casting wheel and the refinery cell. The numbers on the drawing match the numbered steps under How it works. Hover over any part for its name and what it does.