What a gold processing plant does
Gold ore usually holds only a few grams of gold in each tonne of rock. A gold plant frees the gold by grinding, dissolves it with a weak cyanide solution, catches the dissolved gold on activated carbon, strips it off the carbon, plates it out with electricity and melts it into a doré bar (gold with some silver).
The most common route is crush, grind, gravity, leach, carbon, elute, electrowin and smelt. The front of the plant is the same as in any mineral processing plant. What is special to gold is the chemistry after the mills. The animation shows the carbon-in-leach (CIL) route.
How it works
The ore moves through the plant in one line. The carbon moves in a loop, against the slurry.
- 1Crush and grind. A jaw crusher breaks the ore and a conveyor carries it to the mills. The SAG mill and the ball mill grind it with water to a fine slurry. A hydrocyclone sends the coarse part back to the ball mill and passes the fine part on.
- 2Gravity. Cyclone underflow passes through a gravity concentrator, a spinning bowl that holds the heavy, coarse free gold. The rest returns to the mill. This gold does not have to pass through the leach. The gravity concentrate may get its own strong cyanide leach and then joins the gold room.
- 3Condition. The cyclone overflow is thickened (see how a thickener works) and lime is added. The lime holds the pH high, so the cyanide stays as cyanide in the solution and does not turn into hydrogen cyanide gas.
- 4Leach with carbon in the tanks (CIL). The slurry flows by gravity through a row of stirred CIL tanks. Weak sodium cyanide and oxygen dissolve the gold. Activated carbon in the same tanks adsorbs the dissolved gold as fast as it forms. The carbon is moved from tank to tank against the slurry, and screens keep it in each tank.
- 5Elution. Loaded carbon from the first tank is washed, then stripped in an elution column with a hot solution. The gold moves into a small volume of rich solution, the eluate. The stripped carbon is reactivated in a kiln and returned to the last tank.
- 6Electrowinning. The rich solution passes through an electrowinning cell, where an electric current plates the gold onto cathodes as a sludge.
- 7Smelting. The sludge is filtered, dried and melted with fluxes in a furnace, then poured into a mould as a doré bar (see electrowinning and smelting). The leach tailings go the other way: to cyanide destruction and then to the tailings storage facility.
The numbers
Figures are typical and depend on the ore and the site.
| Item | Typical value |
|---|
| Leach residence time | typically 20 to 40 hours |
| Gold recovery in the leach | typically about 90 to 99 percent, depending on the ore |
| Cyanide strength in the tanks | typically about 200 to 500 mg/L |
| pH in the tanks | typically about 10.5 to 11 |
| Dissolved oxygen | typically at least 6 to 8 mg/L |
| Carbon in the tanks | typically about 10 to 20 g of carbon in each litre of slurry |
| Elution temperature | about 130 °C, under pressure |
| Smelting temperature | about 1,200 °C |
The share of the gold that gravity catches varies widely from ore to ore. The tailings are treated to destroy cyanide before they leave the plant, down to the limit set for the site.
Worked example. Assume a plant that treats 5,000,000 t of ore a year and runs 8,000 hours a year. The ore grade is 2.0 g/t and the recovery is 92 percent. The leach feed is 45 percent solids by mass, the ore specific gravity is 2.8, the leach residence time is 24 hours and there are six equal tanks.
| Quantity | Working | Result |
|---|
| Feed rate | 5,000,000 ÷ 8,000 | 625 t/h |
| Slurry specific gravity | 1 ÷ (0.45 ÷ 2.8 + 0.55) | about 1.41 |
| Slurry mass flow | 625 ÷ 0.45 | about 1,389 t/h |
| Slurry volume flow | 1,389 ÷ 1.41 | about 987 m³/h |
| Leach volume for 24 hours | 987 × 24 | about 23,700 m³ |
| Volume of each tank, six tanks | 23,700 ÷ 6 | about 3,950 m³ |
| Gold recovered | 625 × 2.0 × 0.92 | 1,150 g/h, which is 1.15 kg/h |
| Gold in a year | 1.15 × 8,000 | 9,200 kg, about 296,000 oz (31.1 g in one troy ounce) |
Each hour 625 t of rock goes in and just over 1 kg of gold comes out. That is why the plant is built around large tanks and a long residence time: the leach needs time to find the gold.
Assumed inputs, not data from a particular plant.
Safety: sodium cyanide is highly toxic, and it releases hydrogen cyanide gas if the solution turns acid. So pH control, gas monitors and strict handling rules are part of the design. This lesson explains the process; it is not a procedure.
What the operator watches
- Cyanide strength and pH. Too little cyanide slows the leach; a falling pH is a safety alarm as well as a process upset.
- Dissolved oxygen. The leach needs oxygen as well as cyanide, so the oxygen level in the tanks is measured.
- Carbon in each tank. How much carbon there is, how active it is, and how much gold the loaded carbon carries.
- Tailings. The gold left in the tailings is the loss, and the cyanide destruction output must meet the limit before the tailings leave.
Common problems
- Cyanide consumers. Other minerals, such as copper minerals and sulphides, use up cyanide, so the gold dissolves slowly.
- Preg-robbing ore. Some ore holds natural carbon that adsorbs the dissolved gold itself and takes it to the tailings.
- Fouled carbon. Oil or scale on the carbon makes it load poorly.
- Blocked screens. If the screens between tanks block, the carbon does not move as it should and tanks can overflow.
- Low pH. Too little lime lets hydrogen cyanide gas form.
Words you will meet
- Doré
- The bar poured at the mine: gold with some silver. A refinery purifies it later.
- CIL
- Carbon in leach: the gold is dissolved and caught on carbon in the same tanks.
- Free gold
- Gold grains that are loose from the rock after grinding. Coarse free gold can be caught by gravity.
- Preg-robbing
- Ore that takes dissolved gold back out of the solution.
- Loaded carbon
- Carbon that has adsorbed gold and is ready to be stripped.
- Eluate
- The small volume of gold-rich solution that leaves the elution column.
- Electrowinning
- Plating a metal out of a solution onto a cathode with an electric current.
- WAD cyanide
- Weak acid dissociable cyanide: the forms of cyanide that tailings limits are usually written for.
Check your understanding
Why is lime added before the leach?
It keeps the pH high, so the cyanide stays in the solution and does not turn into hydrogen cyanide gas.
What does the carbon in the tanks do?
It adsorbs the dissolved gold as fast as it forms, so the gold leaves on the carbon and is not lost with the tailings.
Why is coarse gold recovered by gravity before the leach?
Coarse gold is slow to dissolve and could be lost. Gravity takes it out early, so it does not have to pass through the leach.