What the crude oil supply chain does
Crude oil is rarely used where it is found. It is lifted from the ground, cleaned of water and gas so that it is safe to move, measured and sold, and then carried by pipeline or tanker to a refinery. At the refinery it is stored, tested and fed to the plant.
This lesson follows the whole chain, from a well to the refinery tanks. Every major unit has a lesson of its own, linked in the steps below. In the animation you can click a unit to open its lesson.
How it works
- 1Wells. Oil comes from onshore wells, where a pumpjack often works a pump deep in the well, and from offshore platforms and floating production vessels. It also comes from subsea wells linked to a platform, from shale wells that are drilled sideways and fractured, and from oil sands, where steam frees the thick bitumen (see SAGD). What comes up is a mixture of oil, gas and water.
- 2Separate. The mixture flows to a separator. Gas rises to the top, oil forms the middle layer and the produced water settles at the bottom. Each leaves by its own outlet. The gas is used, sent away or burned at a flare, and the water is treated.
- 3Stabilise and dehydrate. The crude is heated and goes to a stabiliser, which removes the light gases so that the crude is safe to store and ship. The water and the salt are trimmed to the sales specification. Typical limits are a basic sediment and water (BS&W) content of about 0.5 to 1 percent by volume and a salt content of about 30 to 120 PTB for export. The contract sets the real limit.
- 4Measure. A metering skid called a LACT unit (lease automatic custody transfer) records the volume and the quality of the crude where it changes hands. This is called custody transfer.
- 5Move. Pumps at a pump station push the crude into a pipeline, which is buried for most of its length. Cleaning and inspection devices called pigs are sent through it (see pigging). Thick bitumen from oil sands is mixed with a thinner liquid or upgraded first, so that it can flow. At sea, an FPSO stores the crude in its hull and offloads it to a shuttle tanker.
- 6Terminal. A terminal on the coast stores the crude in tanks, so that the pipeline can keep running between ships. A subsea pipeline carries the crude to a single point mooring (SPM), a buoy at sea where a tanker ties up and loads. Other terminals use a jetty. The tanker then makes the sea voyage.
- 7Refinery receipt. At the refinery jetty the crude leaves the ship and goes into crude tanks. It is tested against the crude assay, the laboratory description of that crude, and blended in the tanks. A pump then feeds it to the desalter, a heater and the distillation column (see the refinery). In some countries most of the crude that refineries use is imported, so it arrives by tanker.
The numbers
Typical figures: some large FPSO hulls hold up to about 2 million barrels of crude. A very large crude carrier (VLCC) also holds about 2 million barrels. The velocity in a crude pipeline is usually about 1 to 2 m/s. One barrel is about 0.159 m³.
Worked example. Assume a pipeline that carries 40,000 barrels a day, and assume an inside diameter of 300 mm. Both are assumed inputs, not data from a real line.
| Quantity | Working | Result |
|---|
| Flow per day | 40,000 × 0.159 | about 6,360 m³/day |
| Flow per hour | 6,360 ÷ 24 | 265 m³/h |
| Flow per second | 265 ÷ 3,600 | 0.0736 m³/s |
| Pipe area | π × 0.15 × 0.15 | 0.0707 m² |
| Velocity | 0.0736 ÷ 0.0707 | about 1.04 m/s |
| Days to fill a 2-million-barrel ship from this line alone | 2,000,000 ÷ 40,000 | 50 days |
Assumed inputs, not data from a particular plant or pipeline. The inside diameter is an assumption, not the size of a real pipe. The velocity is inside the usual range of 1 to 2 m/s. The last row shows why a terminal needs storage tanks: a pipeline of this size fills a big ship slowly, so the crude is collected in the tanks until the ship arrives.
Safety: crude oil and the gas that comes with it burn and can explode when they mix with air, and some crude and gas contain hydrogen sulphide, which is toxic. Oil and gas facilities are controlled areas with strict rules. This lesson explains the idea and is not a procedure.
What the operator watches
- The separator. Levels and pressure, so that gas does not leave with the oil and oil does not leave with the water.
- Quality at the meter. BS&W and salt in the crude where it changes hands.
- The pipeline. Pressure and flow along the line, and the arrival of each pig.
- Tank levels. At the terminal and at the refinery, so that no tank overfills or runs dry.
- The weather at the mooring. Wind and waves decide whether a tanker can load.
Common problems
- Water carry-over. Water that leaves with the oil puts the crude out of specification and brings salt with it.
- Foaming in the separator. Foam takes up room in the vessel and lets liquid and gas leave together.
- Thick crude in a cold line. Wax or heavy oil can thicken in the cold, and the pumps then need more pressure.
- A stuck pig. A pig that stops in the line has to be found and freed.
- An overfilled tank. Crude that runs over is a spill. Levels are watched and alarmed.
Words you will meet
- Wellhead
- The valves and fittings on top of a well.
- Separator
- A vessel that splits the well stream into gas, oil and water.
- Produced water
- The water that comes up with the oil.
- Stabilisation
- Removing the light gases from the crude so that its vapour pressure is safe.
- BS&W
- Basic sediment and water: the solids and water that travel in the crude.
- PTB
- Pounds of salt per thousand barrels of crude.
- LACT
- Lease automatic custody transfer: the metering skid where the crude changes hands.
- Custody transfer
- The point where the oil passes from one owner or operator to the next, and is measured.
- Pig
- A device sent through a pipeline to clean or inspect it.
- FPSO
- Floating production, storage and offloading vessel.
- Shuttle tanker
- A tanker that takes the crude from an FPSO to a terminal or a refinery.
- SPM
- Single point mooring: a buoy at sea where a tanker ties up to load or unload.
- VLCC
- Very large crude carrier.
- Assay
- The laboratory description of a crude: what it is made of and what it yields.
Check your understanding
Why is crude stabilised before it is shipped?
Dissolved light gases would raise the vapour pressure of the crude. They would boil off in the tanks and on the tanker, which is a fire risk and a loss of product. Stabilisation removes them.
Why is salt limited in crude?
Salt corrodes the equipment and fouls it. The refinery takes out most of the salt in its desalter, but the crude is bought with a limit, so that the refinery receives what it expects.
What changes hands at a LACT unit?
The crude. It is measured for volume and quality at the custody transfer point, so that the seller and the buyer agree on what was delivered.
Key facts
- The idea
- Lift the oil, clean it, measure it, move it, store it, deliver it to the refinery.
- The chain
- Well, separator, stabiliser, LACT, pipeline, terminal, tanker, refinery tanks.
- Typical specification
- BS&W about 0.5 to 1 percent by volume, salt about 30 to 120 PTB.
- Size
- An FPSO hull or a VLCC holds up to about 2 million barrels.
Follow the numbers 1–7 on the drawing: they match the steps on this page, in the same order. Crude is shown in dark brown dashes on a tan pipe, gas in pale blue dashes on a dark pipe and water in blue dashes. The dashed white line is the route of the loaded ship. Click a pumpjack, the separator, the stabiliser, the flare, the metering skid, a pump, the pump station or the pipeline, the FPSO, the mooring buoy or a tanker, a tank, the desalter, the refinery heater or the distillation column to open its lesson. The ships and tanks are cut open: watch the levels rise where crude is loaded and fall where it is unloaded. Hover over any part for its name and what it does. The drawing is a sketch and is not to scale.